SS400 Steel

to weld axle tubes or not to weld axle tubes ford

to weld axle tubes or not to weld axle tubes ford

to weld axle tubes or not to weld axle tubes ford

If you Drag Race, PLEASE weld your axle tubes. S197

Jul 04, 2012 · The axle tube itself extends in to the center section and is plug welded from the factory. Under hard launches or alot of wheel hop, the center section and the suspension points put streess on the plug weld. The drive axles themselves ride on a bearing in the outer tube and provide no stress to the tube. Technical - Grinding off TIG weld and welding up my axle Jan 01, 2021 · I took off the braces and finished welding it. I fine tuned the axle tube by grinding the tube close to the casting and welding it back up and quickly cooling it with water. I rotated the DOM tubing and there is no runout that I can feel. The axle bearing adapter I

Welding 8.8 axle tubes? Ford Mustang Forums

Dec 30, 2003 · Correct, you will have to heat up the rear or at least that part of the axle tube, and also will need to use a nickel based welding rod. If not your weld is just as good as using JB WELD on it. Totally useless in other words. Its best to completly gut it. and more than likely it would really not do good with the seals still in it. Welding Axle Tubes to Housing - Miller Welding Discussion Welding Axle Tubes to Housing 04-20-2005, 10:24 PM. Looking to fully weld axles tubes to a cast center section to strengthen a rearend for a drag car. I spoke with someone and they asked if it was cast iron or cast steel. I have no idea what it is. Give me some idea what I can weld it with for strength, because the rear from the factory only Welding Dana 44 Cast Steel Housing - 4-Wheel & Off Nov 01, 2009 · We used a Dana 44 axle as an example on how to fully weld axle tubes to a cast steel axle housing all inside 4-Wheel & Off-Road Magazine. You've ruined the

Welding The Tubes Of An AMC20 - Off-Road Forums

Jan 13, 2000 · Personally I wouldn't weld the tube to the end of the housing. Most axle builders(dynatrac, tri county, etc) say not to do this as it can cause the casting to crack over time. I've been told that Welding diff housing to axle tubes? Pirate 4x4Jun 17, 2003 · You guys are right - you do not want to attempt a structural weld (which is what it would be) between cast or nodular iron (depending on what axle it is) of the diff housing and the mild steel of the axle tubes. I Don't think there's any truth to the "leaving it free to move" story though - it's pretty damned tight inteference fit. Welding tubes to housing on Ford 8.8 axle Pirate 4x4Aug 31, 2009 · First post - What is the best way to weld the axle tubes to the housing on the Ford 8.8 (1997 model) :confused:? Is the housing cast iron or cast steel? Is preheat required and if yes, how much? Should the internals (e.g., bearings) be removed prior to welding? Stick weld with nickel rod or

When to weld axle tubes? Ford Mustang Forum

Mar 09, 2010 · At what horsepower level should you weld the axle tubes on an 8.8? And when is any other bracing a good idea? '87 COUPE, DSS 331, AFR 185's, XE282HR Cam, Victor Jr. Intake, Barry Grant Speed Demon 650, Long Tubes, PA Super Comp C4 When to weld axle tubes? Ford Mustang ForumMar 09, 2010 · At what horsepower level should you weld the axle tubes on an 8.8? And when is any other bracing a good idea? '87 COUPE, DSS 331, AFR 185's, XE282HR Cam, Victor Jr. Intake, Barry Grant Speed Demon 650, Long Tubes, PA Super Comp C4 to straighten or not? axle housing welding The H.A.M.B.Feb 21, 2006 · Be gentile when welding your bracketsweld an inch or so then let it cool and you won't warp your axle tubes. Do NOT cool with water or a wet rag, as that will allow the weld to cool too quickly and become brittle. I had a Ford rear end put in a 38 Ford. I had new spring perches welded on, anti way bar mounts custom made etc.

to straighten or not? axle housing welding The H.A.M.B.

Feb 21, 2006 · Be gentile when welding your bracketsweld an inch or so then let it cool and you won't warp your axle tubes. Do NOT cool with water or a wet rag, as that will allow the weld to cool too quickly and become brittle. I had a Ford rear end put in a 38 Ford. I had new spring perches welded on, anti way bar mounts custom made etc. welding automotive axle housingsDec 06, 2001 · We are looking for a good way to weld DOM steel tubes into the cast steel (not exactly sure on the material) center sections of rear axle housings. We also occasionally need to weld the forged steel knuckles onto the tubes of 4x4 front axle housings. MIG or welding automotive axle housingsDec 06, 2001 · We are looking for a good way to weld DOM steel tubes into the cast steel (not exactly sure on the material) center sections of rear axle housings. We also occasionally need to weld the forged steel knuckles onto the tubes of 4x4 front axle housings. MIG or

welding axle tubes to center section on a 12 bolt Team

Dec 04, 2012 · A Chevelle rear end doesn't put a lot of stress on the axle tubes because of the 4 link suspension. The load is split between the brackets on the axle tubes and the eyes on top of the housing. A Camaro transmits all of the force through the axle tubes, so it's much more important to weld the tubes on a Camaro rear end. Here is something to read. welding axle tubes to center section on a 12 bolt Team Dec 04, 2012 · A Chevelle rear end doesn't put a lot of stress on the axle tubes because of the 4 link suspension. The load is split between the brackets on the axle tubes and the eyes on top of the housing. A Camaro transmits all of the force through the axle tubes, so it's much more important to weld the tubes on a Camaro rear end. Here is something to read. welding axle tubes.preventing damage [Archive] - Pro The best way would be to grind the paint and prep the axle tubes for welding. Tack the brackets in place with the housing in the car. Remove the rear end from the vehicle, remove the axles from the housing, then finish welding. Check the axle tubes for warpage (make sure the housing ends are parallel). Straighten as necessary. Re-install.

Ford 8.8 axle housing, to weld or not to weld? - The

Mar 14, 2013 · For my leaf spring set up - I welded the tubes to the center section with the tig - only time will tell if that helped or not. I've contemplated adding a "spine" to the axle tubes welded to the center section - similar in design to what the big guys run - but for my application - probably not needed at all -

Contact us

Email: [email protected]